• HOME

  • Calender of Events

  • THE PRACTICE

  • STAFF

  • INSURANCE

  • NEW PATIENTS

  • APPOINTMENTS

  • CLINICAL CONDITIONS

  • RESOURCES

  • CONTACT

  • Blog

  • Forum

  • MORE

    8180 Lark Brown Road
    Suite 101
    Elkridge, MD 21075

    (443) 755-0030
    (443) 755-0031

    Parkinson's & Movement Disorders Center of Maryland

    Dr. Stephen E. Grill, MD, Ph.D
    Make an Appointment

    PDMD Center of Maryland

    8180 Lark Brown Road

    Suite 101

    Elkridge, MD 21075

    For Life-Threatening Emergencies Call 911

    © 2016 by PDMD Center of MD. Proudly created with Wix.com

    1. Your Forum
    2. PD Motor Fluctuations
    3. Advances in Parkinson’s Disease Treatment
    Search
    utpawspt
    Apr 9, 2018

    Advances in Parkinson’s Disease Treatment

    0 comments

     

    In honor of Parkinson's Awareness Week, we are sharing the new and exciting discoveries in Parkinson's disease treatment. Drs. Han-Lin Chiang and Yih-Ru Wu, leaders in Parkinson's disease research, discuss some of the most promising advancements in the treatment of Parkinson's disease.

    It has been 200 years since Dr. James Parkinson published the An Essay On the Shaking Palsy describing the signs and symptoms of Parkinson’s disease (PD). Despite the fact that there are lots of treatment options out there to ameliorate the patient’s symptoms and to improve their quality of life, we still don’t have any neuroprotective or disease-modifying therapy to slow down disease progression. But for patients with PD, the past few years have never been so hopeful in that new candidate therapies are being developed at a very fast pace.

     

    For More You Can Check:

    Blockchain Application Marketing

     

    0
    New Posts
    • utpawspt
      Jun 1, 2018

      Tool height fluctuation during operation

      Hey everyone, I'm running a CNC router (Pacer 4010). I have been noticing lately that my tool height has been increasing and decreasing in height as I'm running a program. I thought my waste board was uneven but when I go to tool tip my bit, I'll be getting a lower or higher measurement than when I first measured it in the start of running my sheet. I'm not sure what would cause this. I thought maybe my bit is slipping a little bit inside the collet but I checked that and it was nice and tight. Could the cone be slipping down a little bit in the spindle? Has anyone heard of this and would happen to know the possible cause? Please help. I didn't find the right solution from the Internet. References:- http://forum.vectric.com/viewtopic.php?f=3&t=29151 Auto loan marketing Thanks
      0 comments
      0
    • utpawspt
      Jun 1, 2018

      Synchronizing Tetrix Motors

      Hello, Our robot has scissor lift which is run by four tetrix motors powered by a 12V external battery pack, two on the right side, two on the left side. The way they are currently set up, the two motors on each side absolutely must run at the same speed, otherwise they will strip gears and unleash all sorts of havoc. What we would like to know is: How can we synchronize each set of motors together in such a way that they will each get full power and that they will each be running at the same, constant speed? Please help. I didn't find the right solution from the Internet. References:- http://www.robotc.net/forums/viewtopic.php?f=1&t=5401 Data Analysis Software Video Thanks
      0 comments
      0
    • utpawspt
      May 2, 2018

      Recommendations on Balsamic Vinegar?

      Hi, I love balsamic vinegar with olive oil for dipping. And on summer tomatoes and salads. We usually buy random stuff in the supermarket. Sometimes they are good. Sometimes they are awful like the one I just had to throw in trash on first taste. For more details Business Promotional Videos
      0 comments
      0